TurboChef F6: the electrical compartment is overheating
EC means electrical compartment.
Mon–Sat, 8am–8pm
- Blowers and airflow
- Pizza oven blower and fan repair
- Source: TurboChef
Book a visit
Three short steps, about a minute.
or call (844) 747-3662
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F6
actually means.
EC means electrical compartment. Small fans pull room air past the boards and relays, and F6 appears when that compartment runs hot. TurboChef points at paper towels or other items blocking the cooling air, clogged rear fan guards on the Single Batch, and cooling fans that have stopped.
TurboChef pizza oven display · also shown as F6: EC Over Temp, F6: EC Temp
What to do when F6 shows on the pizza ovenKind of codeBlowers and airflow
The air the oven bakes with is not moving as it should. In a conveyor or rapid-cook oven the impingement blower may be dragging on worn bearings, its fingers packed with grease so the jets fire unevenly, or its cooling fan clogged with flour dust until the controls overheat; a gas oven may also refuse to light when its combustion air switch never proves. Cleaning the intake filters and grilles with the oven off is safe; a blower that slows, squeals or smells hot is a visit.
Usually leads toPizza oven blower and fan repair
Impingement blowers, cooling fans, bearings, belts and air fingers repaired or replaced, so hot air reaches every lane of the pizza oven evenly.
Shows up asPizza Oven Error Code on a Deck, Conveyor or Rapid-Cook Display
A pizza oven error code shows as letters or numbers on the display of a conveyor, deck or rapid-cook oven, a flashing light on its panel, or a message about ignition, heat, belt or airflow.
MakeTurboChef
A TurboChef call starts with the menu item that came out wrong and the recipe setting it ran on, since a rapid-cook oven follows those settings to the second.
SourceTurboChef High h Conveyor (HhC 1618, 2020, 2620) owner's manual, HCT-4201 Rev U
HhC conveyors (legacy controller) print F6: EC Over Temp; the Single Batch prints F6: EC Temp and adds the rear cooling fan exhaust guards as a cause.
Before you book,
in this order.
Each step comes from TurboChef's own guidance for F6 on its pizza ovens. Follow it to the end: the last card says whether this is a visit.
Pull anything away from the side and rear panels, including towels, bags and stock stacked against the oven.
On a Single Batch, check that the rear cooling fan guards are free of lint and grease; clean them only with the oven off.
Keep the air around the oven reasonable; if F6 comes back with the panels clear, book a visit so the cooling fans can be checked.
Still there?
It usually turns into pizza oven blower and fan repair. Book with the code and the model number.
What not to do
F6 does not say the food is overcooking; the cook chamber has its own overheat report, F5. It is also not a blower report for the main cooking air, which is F1.
What you may
notice with it.
The pizza oven problems F6 tends to arrive with. Answer these at the pizza oven before anyone is booked.
All problems
Where F6 usually leads
Pizza oven blower and fan repair.
TurboChef
pizza ovens.
A TurboChef call starts with the menu item that came out wrong and the recipe setting it ran on, since a rapid-cook oven follows those settings to the second.
TurboChef pizza oven repair
In TurboChef's own words
F6: EC Over Temp
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. HhC conveyors (legacy controller) print F6: EC Over Temp; the Single Batch prints F6: EC Temp and adds the rear cooling fan exhaust guards as a cause.
TurboChef F6 pizza oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F6.
Can I clear F6 myself?
Why does my TurboChef show F6 after we moved it against a wall?
Where are the cooling fans on a TurboChef Single Batch?
Does a hot kitchen trigger TurboChef F6?
Back to your everyday
Still showing F6?
A booking with a code goes further when it has the code copied as shown, the model and serial from the rating plate, and a note on whether the oven still lights, heats or moves its belt. With those three, the office can match the likely part to your oven the same day.