Middleby Marshall RESET IGNITION: the gas burner did not light or went out
Each time a Middleby Marshall gas conveyor starts, it purges the chamber with the blower, sparks the burner and proves the flame.
Mon–Sat, 8am–8pm
- Ignition and flame
- Pizza oven burner and igniter repair
- Source: Middleby Marshall
Book a visit
Three short steps, about a minute.
or call (844) 747-3662
Loading appointment form…
The appointment form couldn’t load. Please try again.
What RESET IGNITION
actually means.
Each time a Middleby Marshall gas conveyor starts, it purges the chamber with the blower, sparks the burner and proves the flame. If that sequence ends without a steady flame, the X-Series shows RESET IGNITION. The manual gives three causes: gas not turned on to the oven, gas pressure too low and a burner that has stopped running.
Middleby Marshall pizza oven display
What to do when RESET IGNITION shows on the pizza ovenKind of codeIgnition and flame
The oven tried to light its burner and never proved a flame, or proved one and then lost it. The usual reasons are ordinary: a gas shutoff not fully open or a tank running dry, an igniter cracked or crusted with flour dust, a flame sensor or thermocouple that no longer reads the heat, or a draft that pulls the pilot away from it. Checking the shutoff and the tank and running the restart the manual names are fair first steps; if you smell gas, get outside first, and the valve, the sensor and every fitting stay with a technician.
Usually leads toPizza oven burner and igniter repair
Pizza oven burners cleared or replaced and igniters fitted and gapped, so the flame lights first time and burns blue and steady under the stone.
Shows up asPizza Oven Error Code on a Deck, Conveyor or Rapid-Cook Display
A pizza oven error code shows as letters or numbers on the display of a conveyor, deck or rapid-cook oven, a flashing light on its panel, or a message about ignition, heat, belt or airflow.
MakeMiddleby Marshall
A Middleby Marshall conveyor call is about the line: how many pies came out right before the belt slowed, stalled or the crust went pale.
SourceMiddleby Marshall X70G, X55G, X55GWB gas oven owner's operating and installation manual (78866 Rev F)
X70G, X55G and X55GWB gas conveyors (owner's manual 78866 Rev F). The PS638G gas oven covers the same condition in its troubleshooting table as an oven not heating because the burner has stopped running.
Before you book,
in this order.
Each step comes from Middleby Marshall's own guidance for RESET IGNITION on its pizza ovens. Follow it to the end: the last card says whether this is a visit.
Press Dismiss and follow the prompts on the screen.
Make sure the manual gas valve on the supply to the oven is open, as it may have been shut for cleaning or after a delivery.
Turn the oven off and back on to clear the message and let it run its own relight sequence; do not try to light the burner any other way.
If RESET IGNITION returns, or you smell gas at any point, turn the oven off, close the gas supply and book a visit; a gas smell means leaving the area and calling the gas utility from outside.
Still there?
It usually turns into pizza oven burner and igniter repair. Book with the code and the model number.
What not to do
RESET IGNITION is not a temperature sensor report; the probes have their own messages, PROBE # OPEN and ALL PROBES OPEN. An oven that lights but never reaches its set point shows HEATING ERROR instead.
What you may
notice with it.
The pizza oven problems RESET IGNITION tends to arrive with. Answer these at the pizza oven before anyone is booked.
All problems
Where RESET IGNITION usually leads
Pizza oven burner and igniter repair.
Middleby Marshall
pizza ovens.
A Middleby Marshall conveyor call is about the line: how many pies came out right before the belt slowed, stalled or the crust went pale.
Middleby Marshall pizza oven repairMore Middleby Marshall codes
Ignition and flame on other makes
In Middleby Marshall's own words
Oven burner failed to light / stays lit.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. X70G, X55G and X55GWB gas conveyors (owner's manual 78866 Rev F). The PS638G gas oven covers the same condition in its troubleshooting table as an oven not heating because the burner has stopped running.
Middleby Marshall RESET IGNITION pizza oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about RESET IGNITION.
Can I clear RESET IGNITION myself?
How many times does a Middleby Marshall conveyor try to relight?
Why does my Middleby Marshall X55 show RESET IGNITION every morning?
Is RESET IGNITION dangerous on a Middleby Marshall?
Back to your everyday
Still showing RESET IGNITION?
A booking with a code goes further when it has the code copied as shown, the model and serial from the rating plate, and a note on whether the oven still lights, heats or moves its belt. With those three, the office can match the likely part to your oven the same day.