Blodgett LOAD: the 1415 deck is waiting for a cook time
After the temperature has been set with the TEMP key and the dial, the 1415 display reads LOAD.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Blodgett
Book a visit
Three short steps, about a minute.
or call (844) 747-3662
Loading appointment form…
The appointment form couldn’t load. Please try again.
What LOAD
actually means.
After the temperature has been set with the TEMP key and the dial, the 1415 display reads LOAD. That is the point in the sequence where the cook time is set with the TIME key and the product goes onto the stone.
Blodgett pizza oven display · also shown as load
What to do when LOAD shows on the pizza ovenKind of codeMode, not a failure
No part of the oven has failed; the display is reporting a state someone chose or the oven entered on its own. A cool-down keeps the blowers turning after the heat is off until the cavity or the tunnel has dropped to a safe level, an energy save setting lets the decks sag between rushes, and a menu lock stops anyone on the line from changing the bake times. No part is needed: letting the cool-down run out, or the key sequence in the manual, brings the oven back.
Usually leads toNo repair
Press the TIME key and turn the dial to the cook time you want.
Shows up asPizza Oven Error Code on a Deck, Conveyor or Rapid-Cook Display
A pizza oven error code shows as letters or numbers on the display of a conveyor, deck or rapid-cook oven, a flashing light on its panel, or a message about ignition, heat, belt or airflow.
MakeBlodgett
At a Blodgett deck oven the tech starts by asking the cook which deck, which spot on the stone and which hour of the shift the bake went wrong.
SourceBlodgett 1415 countertop electric deck oven installation, operation and maintenance manual
Blodgett 1415 countertop deck ovens with the digital display, dial and START/STOP, TIME and TEMP keys.
Before you book,
in this order.
Each step comes from Blodgett's own guidance for LOAD on its pizza ovens. Follow it to the end: the last card says whether this is a visit.
Press the TIME key and turn the dial to the cook time you want.
Load the product onto the deck stone and press START/STOP to begin the countdown.
If LOAD never appears after you set a temperature, or the display will not respond to the keys, switch the oven off and book a visit for the control.
Cleared?
The code has left the display, the decks or the tunnel come up to the set heat and hold it through a full service, the belt keeps its speed and the blowers run steady, all with no part changed. If the same code returns within a week, or on the next busy night, say so when you book.
What not to do
LOAD does not say the stone has reached temperature; the manual only ties it to the next step of the setup. It is not an alarm and needs no reset.
What you may
notice with it.
The pizza oven problems LOAD tends to arrive with. Answer these at the pizza oven before anyone is booked.
All problems
No repair indicated
Nothing to repair.
No part of the oven has failed; the display is reporting a state someone chose or the oven entered on its own. A cool-down keeps the blowers turning after the heat is off until the cavity or the tunnel has dropped to a safe level, an energy save setting lets the decks sag between rushes, and a menu lock stops anyone on the line from changing the bake times. No part is needed: letting the cool-down run out, or the key sequence in the manual, brings the oven back.
Blodgett
pizza ovens.
At a Blodgett deck oven the tech starts by asking the cook which deck, which spot on the stone and which hour of the shift the bake went wrong.
Blodgett pizza oven repairMore Blodgett codes
Mode, not a failure on other makes
In Blodgett's own words
When the display reads LOAD, press the TIME KEY
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Blodgett 1415 countertop deck ovens with the digital display, dial and START/STOP, TIME and TEMP keys.
Blodgett LOAD pizza oven repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about LOAD.
Can I clear LOAD myself?
What does LOAD mean on a Blodgett 1415 deck oven?
Should I wait before loading when my Blodgett 1415 reads LOAD?
How do I set the temperature on a Blodgett 1415?
Back to your everyday
Still showing LOAD?
A booking with a code goes further when it has the code copied as shown, the model and serial from the rating plate, and a note on whether the oven still lights, heats or moves its belt. With those three, the office can match the likely part to your oven the same day.